سنگ شکن a مشترک تجهیزات در که a کلید جزء بلبرینگ بلبرینگ مکانیکی عناصر که تبدیل چرخش حرکت به محوری حرکت یا محوری حرکت به دوار حرکت به دوار حرکت . Due به سنگین بار کاری و طولانی از استفاده ٪ 2c یاطاقان ممکن است اسیب دیده یا دیگر مشکلات ٪ 2c در این زمان نیاز به می شود جدا کردن. .
Step 1: Preparation
٪0aBefore disassembling٪2c it is necessary to turn off the power supply and system of the crusher. Then٪2c you need to select suitable tools according to the specification and model of the crusher٪2c and prepare the disassembly tools you need to use٪2c such as hammer٪2c wrench٪2c scraper٪2c punch and so on.
مرحله 2٪ 3a جداسازی قطعات
٪0a1. Remove the bearing cover. Secure the upper nut and washer of the bearing with a tube٪2c and then secure the bearing seat with a wire rope. the bearing cover can be easily removed by turning the lower nut slightly with a a wrench to loosen the bearing.
2. Remove the outer ring. Use a wire brush to clean the bearing housing to ensure accurate disassembly, otherwise the bearing housing will be damaged. Use the appropriate tool to disassemble the outer ring of the bearing and remove it from the shaft. If the outer ring cannot be removed, the inner ring of the bearing must be removed first. When removing the outer ring, be careful not to twist or distort it.
٪0a3. Remove the inner ring. Use appropriate tools to disassemble the inner ring of the bearing. The inner ring must be removed very carefully to avoid damage to the internal gears or other components.
Step 3: Installation
٪0aهنگامی که جداسازی قطعات کامل است٪2c the new bearing must be installed on the crusher. The installation process requires attention to the the following points٪3a
1. تمیز کردن قطعات. قبل از اقدام با نصب ٪ 2c مطمئن شوید برای تمیز کردن بلبرینگ و پاشنه بخش جایی که بلبرینگ واقع شده است . اطمینان حاصل کنید تخت سطوح کامل و ازاد از اسیب و باقی مانده است.
٪0a2. Assemble the inner and outer rings. Slide the inner ring into the shaft and lock it in place٪2c tapping lightly to bring the bearing set into the proper position. Slide the outer ring of the bearing into the housing and lock it in place.
٪0a3. Inspect the bearing. Perform a test run after installation. Note that the run time should not be too long.
برای خلاصه کردن
٪ 0a بالا روش از جداسازی و مونتاژ سنگ شکن تحمل است. در طول عملیات٪ 2c مراقب باشید و محتاط٪ 2c و انجام ندهید به راحتی اسیب تجهیزات و اجزاء. هنگامی که نصب٪ 2c با دقت بررسی که هر بخش ثابت است در درست موقعیت استفاده کنید درست ابزار و روش برای جداسازی قطعات و مونتاژ برای اطمینان طولانی مدت پایدار عملیات از دستگاه دستگاه.
قطعات یدکی قطعات برای EI جی مخروط سنگ شکن

